Show Full Spec Comparison
| Sire Larry Carlton S10 SSS | Jackson X Series Soloist SLX LH | |
|---|---|---|
| General | ||
| Brand: | Sire | Jackson |
| Year: | 2024 | 2020 |
| Configuration: | SSS | HH |
| Strings: | 6 | 6 |
| Made in: | Indonesia | Indonesia |
| Series: | S | X |
| Colors: | Sunburst, Natural | Black Satin |
| Left-Handed Version: | Yes | No |
| Body | ||
| Type: | Solid Body | Solid Body |
| Body Material: | Swamp Ash | Poplar |
| Bridge: | Gotoh 510TS-SF1 Gold | Floyd Rose Special Double-Locking Tremolo (Recessed) |
| Neck | ||
| Neck Joint: | Bolt-On | Neck-Through |
| Tuners: | Sire Premium Locking Tuner | Jackson Sealed Die-Cast |
| Fretboard: | Hard Maple Edgeless (Rolled Fretboard Edges) | Laurel |
| Neck Material: | Hard Maple | Maple |
| Decoration: | Abalone dot | Pearloid Sharkfin |
| Scale Size: | 25.5" | 25.5" |
| Shape: | C-Shape | Jackson Standard |
| Thickness: | 1st Fret: 0.9'' (22.9mm) - 12th Fret: 0.94'' (23.9mm) | 1st Fret: 0.79'' (20.1mm) - 12th Fret: 0.85'' (21.6mm) |
| Frets: | 22 Medium Jumbo Stainless Steel | 24 Jumbo Nickel Silver |
| Fretboard Radius: | 12" to 14" | 12" to 16" |
| Nut: | Bone | Locking |
| Nut Width: | 42mm (1.654'') | 42.9mm (1.688'') |
| Electronics | ||
| Bridge Pickups: | Seymour Duncan Single Coil (Single Coil / Passive) | Duncan Designed HB-103B (Humbucker / Passive) |
| Middle Pickup: | Seymour Duncan Single Coil (Single Coil / Passive) | |
| Neck Pickup: | Seymour Duncan Single Coil (Single Coil / Passive) | Duncan Designed HB-103N (Humbucker / Passive) |
| Switch: | 5 Way | 3 Way |
| Knobs: | Bell | Dome |
| Pickup Mods: | None | None |
| Volume Controls: | 1 | 1 |
| Tone Controls: | 2 | 1 |
| Hardware | ||
| Strap Lock: | No | No |
| Hardware Color: | Gold | Black |
Show Diagrams Comparison
Reasons to Get
Sire Larry Carlton S10 SSS over Jackson X Series Soloist SLX LH
Reasons to Get
Jackson X Series Soloist SLX LH over Sire Larry Carlton S10 SSS
Other Key Differences
Sire Larry Carlton S10 SSS vs Jackson X Series Soloist SLX LH
Shared Features
Sire Larry Carlton S10 SSS vs Jackson X Series Soloist SLX LH
Common Strengths
- High-Quality Nut
- Compound Radius Fretboard
Common Weaknesses
- Pickup Alter Switch/Knob
- Weight Relief
- Stays in Tune (Evertune)
- From a High-Quality-Standards Country
- Luminescent Sidedots
- Strap Lock
- 21:1 Tuner Ratio
- Active/Passive Preamp
Price History Comparison
These are affiliate links. We may earn a fee if you purchase after clicking. These prices are prone to error. Make sure you're buying the right product after clicking on a link from our site. We are not liable if you buy the wrong product after following these links. As an Amazon Associate site we earn from qualifying purchases.
Hand Size Comfortability
After taking into account the scale length, nut width, neck profile and fretboard radius, we can conclude that both favor small hands .
Sire Larry Carlton S10 SSS:
Jackson X Series Soloist SLX LH:
Beginner Friendliness
The Sire Larry Carlton S10 SSS meets 7 out of our 8 criteria items for beginner friendliness, while the Jackson X Series Soloist SLX LH meets only 4. This takes into account the type of frets, scale length, nut width, bridge type, fretboard radius, and neck profile to determine the easiest combination for new players.
New Player Friendliness
Sire Larry Carlton S10 SSS- Comfortable shape
- Easy-to-use bridge
- Locking tuners
- Comfortable fretboard
- Tall frets
- Narrow nut
- Comfortable neck
- Short scale
New Player Friendliness
Jackson X Series Soloist SLX LH- Comfortable shape
- Comfortable fretboard
- Tall frets
- Comfortable neck
- Narrow nut
- Short scale
- Locking tuners
- Easy-to-use bridge
Sound Quality Comparison
The wood used in an electric guitar or bass is not as important to determine the final tone. However, some people prefer specific wood types, so we'll take a look at those first. Then, we'll take a look at the electronics to determine the versatility and sound quality of each instrument.
Woods Used in Both
Maple is one of the most popular necks for good reasons. It is a strong wood that is relatively cheap to make and looks beautiful. The highest quality maple is the hardest that comes from North America. Find out more about Maple.
Woods Used in the Sire Larry Carlton S10 SSS
Ash is a type of wood that Fender used almost exclusively in the 50s, and it's still used by many brands. It's a dense wood with a light color that works well for a transparent, natural finish because of its beautiful patterns. In terms of sound, it's known for emphasizing the mid and high frequencies, but with strong low end. Find out more about Ash.
Woods Used in the Jackson X Series Soloist SLX LH
There are many types of Laurel, but East Indian is the most common for guitar building. Its color can vary from dark to light brown with black lines. Many people find its tonality similar to Rosewood, which favors the warmer frequencies. Find out more about Laurel.
Poplar is a cheaper and heavier alternative to Alder wood. It terms of tone, it emphasizes the low-end and has cutting mids. It's relatively soft compared to most body woods. Find out more about Poplar.
Winner: Sire Larry Carlton S10 SSS.
Pickup Configuration
The Sire Larry Carlton S10 SSS has an SSS configuration while the Jackson X Series Soloist SLX LH has HH pickups.
SSS is perfect for players who like to play clean. The definition you get between notes and the crispiness is unmatched by most other configurations. You can still use it for distortion, but you won't get the same kind of output and power compared to a humbucker, and the hum they produce also makes them less adequate for high gain.
On the other hand, Double Humbucker (HH) is the choice for people who want a fuller, more round sound with tons of mids and lows. Humbuckers also get rid of the hum noise that plague single-coil pickups. They can work out for almost any genre going from Djent to even Jazz.
Pickups Quality
The Sire Larry Carlton S10 SSS has pickups from a more specialized brand than the Jackson X Series Soloist SLX LH. Its pickups should simply give you a better, fuller sound, although it all depends on what type of music you're going to play. We recommend these pickups for Funk and similar genres.
Both use Passive pickups. This is what's used for most music genres. They have a regular output and will serve you for both high-gain and clean tones. The alternative (Active pickups) offer a higher output that is mostly used for heavy music.
Winner: Sire Larry Carlton S10 SSS.
Versatility Comparison
Some instruments offer you more ways to explore your creativity than others. Below you'll find how both compare when it comes to versatility.
Switch Options
The Sire Larry Carlton S10 SSS gives you 5 switch options while the Jackson X Series Soloist SLX LH gives you 3. This means that the Sire Larry Carlton S10 SSS gives you more options to find the right pickup combination for the type of sound you want to achieve
Neither of them come with some kind of coil split or pickup mod option. This makes both lacking in terms of versatility.
When evaluating versatility, we also take into consideration bridge and neck joint type, number of frets, switch options, amount of pickups and more.
Winner: Sire Larry Carlton S10 SSS.
Final Sound Quality Scores
Build Quality Comparison
When it comes to build quality, we like to take into account everything used to build the instrument. This includes materials, hardware and the quality control expected depending on the country where it was built. Let's see how the Sire Larry Carlton S10 SSS compares to the Jackson X Series Soloist SLX LH.
Country of Origin
The manufacturing country can tell a lot about the build quality of an instrument. Both in this comparison where made in Indonesia.
Indonesia is becoming the most popular country for guitar building because they can make good instruments for a low price. Some people think that they're 'the new China' when it comes to build quality. But the truth is that Indonesian guitars are more consistent, although Chinese quality has improved a lot in the last few years.
Winner: Tie
Nut Material
If you want your guitar to stay in tune and sound good, you need a well cut nut. Nut quality can be inconsistent even when comparing two copies of the same model. The best way to make sure you're nut will be well done is by getting a nut made by an expert company like TUSQ or Micarta.
The Sire Larry Carlton S10 SSS has a Bone nut. It's a type of nut found in high-quality instruments. They sound similar to Ivory since they give a lot of sustain and a bright sound (at least when striking open strings). The only problem they can run into is that you may get a bone piece that simply doesn't sound as well as others because that's just how natural materials are.
On the other hand, the Jackson X Series Soloist SLX LH comes with a Locking nut. Instead of a regular nut, this guitar has a locking system that will lock down the strings at the nut, preventing it from getting out of tune. It removes one of the disadvantages of tremolo bridges, tune stability.
Winner: Tie.
Fret Material
Most fret wire is made of nickel silver. This material eventually wears down after a lot of use and most instruments end up needing a complete fret replacement. However, some expensive models come with stainless steel frets. This is what you should aim for if you can afford it.
In this comparison, the Sire Larry Carlton S10 SSS is the only one that has stainless steel frets. These frets will basically last for the entire life of the guitar. They will never need polishing nor replacement. And not only that, but some people also notice that bending and vibratos are much easier to perform when they upgrade to stainless steel.
Winner: Sire Larry Carlton S10 SSS.
Bridge
The perfect bridge for you will depend on your playstyle because they all have advantages and disadvantages. However, some bridges are more expensive—like Floyd Roses and Evertunes—and thus add more value to a guitar.
The Sire Larry Carlton S10 SSS's brige is a Tremolo. Tremolo bridges give you more versatility than fixed bridges. They let you perform the intense vibrato effects that would be impossible with a fixed bridge. However, since the bridge floats and there's less contact with the body, the strings lose sustain slightly faster. They can also be a bit harder to restring and set up correctly than fixed bridges.
On the other hand, the Jackson X Series Soloist SLX LH's is a Floyd Rose. This is a double-locking bridge system that allows you to perform techniques like dive bombs and pinch harmonics. The locking nut allows your guitar to stay in tune even after the most intense tremolo usage. The disadvantage is that it takes more work to change the strings and set up everything correctly.
Since we need to be objective, the most expensive type of bridge will be the winner of this section. In the end, this doesn't matter if you're not going to use the bridge for its original purpose, so choose the bridge that fits your playing style better.
Winner: Jackson X Series Soloist SLX LH.
Tuners
The Sire Larry Carlton S10 SSS has the best tuners of the two because they are locking tuners. They'll help to keep your guitar in tune because they allow you to tune it without wrapping the strings around the posts. This avoids variations in the tuning due to the strings changing position at the post after a bend. They come at the disadvantage of being slightly heavier than regular tuners. Also, it makes it a lot easier to restring.
Nevertheless, the Jackson X Series Soloist SLX LH has a locking nut, so it should have even better tune stability and doesn't need locking tuners.
Winner: Sire Larry Carlton S10 SSS.
Neck Joint
Contrary to popular belief, the difference in sustain and tone that some neck joints give to a guitar is simply unperceivable—if they're all well built. However, some of them do have advantages over the others.
The Sire Larry Carlton S10 SSS has a Bolt-On neck joint. This neck is joined to the body by 4 bolts that you can simply unscrew. This allows you to replace the neck or take it off for travel. It's the most common and cheapest way to build a guitar.
On the other hand, the Jackson X Series Soloist SLX LH comes with Neck-Through neck joint. This neck is a lot more resistant and lets builders give the neck joint a more comfortable shape for soloing at the upper frets. The disadvantage is that they're more expensive and that if you damage your neck, you can't simply replace it like with bolt-on necks.
Winner: Jackson X Series Soloist SLX LH.
Here is the list of features that were considered when choosing the winner in the Features subcategory:
Sire Larry Carlton S10 SSS
- Stainless Steel Frets
- Locking Tuners
- Expensive Wood
- Bone Nut
- Top Brand Pickups
- Tremolo
- Compound Radius Fretboard
- Made in Indonesia
- No Neck-Through Build
- No Push Knob or Extra Switch Option
- No Weight Relief
- No Luminescent Inlay
- No 21:1 Tuner Ratio
- No Strap Lock
Jackson X Series Soloist SLX LH
- Locking Nut
- Neck-Through Build
- Tremolo
- Compound Radius Fretboard
- Cheap Fret Wire (NS)
- No Locking Tuners
- Made in Indonesia
- No Expensive Woods
- No Top Brand Pickups
- No Push Knob or Extra Switch Option
- No Weight Relief
- No Luminescent Inlay
- No 21:1 Tuner Ratio
- No Retainer Bar
- No Strap Lock
Final Build Quality Scores
Playability Comparison
Let's now compare their playability. Bear in mind that the instrument will feel different depending on your hand size and play style. That's why you should always test before buying. But if you can't or want a second opinion on it, we can still take a look at each of the important measurements of the instrument for you. This way, we can predict how easy a guitar might be to play, or how different it will feel compared to the other.
Remember that, even though the difference might seem small, every inch counts when it comes to feeling of the instrument in your hands. Any variation can completely change how comfortable a guitar feels in your hands.
Nut Width
The nut width will affect the separation between strings at the nut. In this comparison, the Jackson X Series Soloist SLX LH has the wider nut with 42.9mm (1.688'') vs 42mm (1.654''). This is a 0.9mm (0.034'') difference
This means that it will be more difficult to do bar chords on the Jackson X Series Soloist SLX LH, especially closer to the nut. However, it's also easier to play without muting strings accidently. This favors people with big hands.
Scale Length
The scale length is one of the things that influences playability the most. This is the distance between the nut and the bridge and will affect everything from low action allowance, difficulty to perform bends, fret separation, and even tone.
In this case, both have a scale length of 25.5".
This is the scale used in most Stratocasters. It's slightly longer than the typical 24.75'' size found in Les Pauls, and it's one of the main reasons why Stratocasters have such a bright sound in general. A longer scale also means that the strings will have higher tension. This will help you get lower action without suffering fret buzz, which will also be helpful when playing in lower tunings without having to increase your string gauge.
However, this also means that there will be more separation between frets, which can make it more difficult to play. Also, bending the strings will require more strengths due to the increased tension, but remember that a tremolo guitar will offset this difficulty.
Lastly, remember that you can also affect the tension of the strings by changing your string gauge. You can use a thicker gauge for more tension and a lighter one for less tension.
Neck Profile
No single neck shape is better than others. However, most people tend to prefer a thinner necks because it doesn't get in their way when playing fast and most hand sizes can adapt to it pretty well. However, some people still prefer thicker necks for a better grip, especially if they have big hands.
In this case, both have different neck shapes:
The Sire Larry Carlton S10 SSS has a C type of neck. This is what you'll find in most modern guitars. Most people feel like the thickness of a C neck is simply the less intrusive one for playing fast, while at the same time allowing you to grab the neck easily for resting if you want to.
The Jackson X Series Soloist SLX LH, on the other hand, has a D neck. This is a thin and flat neck that is made for playing fast. If you prefer a neck that doesn't get in your way when soloing, this is the shape you should use. Guitarists that prefer to have a bit more grip won't like this type of neck.
Fretboard Radius
Most guitar fretboards are not flat; they usually have a curve or arc across their width. A curved fretboard will make it easier to perform chords without muting strings, while a flatter one will make it easier to play single notes, which is good for bending and soloing in general. The best fretboards have a compound radius that varies across the fingerboard, but they're not common since they take a lot more work to build.
Both have a compound radius. This means both offer you the best craftsmanship when it comes to fretboard design. You'll have an arc to help you play chords close to the nut, while also having a flat design at the higher frets for faster soloing and easier bends.
Fret Size
The Jackson X Series Soloist SLX LH has Jumbo frets, which should be taller than the Sire Larry Carlton S10 SSS's Medium Jumbo frets.
Some people prefer taller frets because they result in more sustain since the strings get pressed cleanly without interference from the fretboard. However, if they're too tall—like Jumbo frets—, you might change the pitch of the strings accidentally if you press too hard because you won't be touching the fretboard with your fingers. This is also why some guitarists with a heavy grip prefer smaller frets. They like to feel the fingerboard to avoid pressing down too hard and getting out of pitch.
