Show Full Spec Comparison
| PRS SE NF3 | SE DGT | |
|---|---|---|
| General | ||
| Brand: | PRS | PRS |
| Year: | 2024 | 2023 |
| Configuration: | HHH | HH |
| Strings: | 6 | 6 |
| Made in: | Indonesia | Indonesia |
| Series: | SE | SE |
| Colors: | White, Black, Blue, Red | Gold, Sunburst |
| Left-Handed Version: | No | No |
| Body | ||
| Type: | Solid Body | Solid Body |
| Body Material: | Poplar | Mahogany |
| Bridge: | PRS Patented Tremolo | PRS Patented Tremolo, Molded |
| Neck | ||
| Neck Joint: | Bolt-On | Set |
| Tuners: | PRS Designed | PRS Designed Tuners |
| Fretboard: | Rosewood | Rosewood |
| Neck Material: | Maple | Mahogany |
| Decoration: | Birds | Moons or Birds (finish dependent) |
| Scale Size: | 25" | 25" |
| Shape: | Wide Thin | DGT |
| Thickness: | 1st Fret: 0.82'' (20.8mm) - 12th Fret: 0.91'' (23.1mm) | 1st Fret: 0.84'' (21.3mm) - 12th Fret: 0.93'' (23.6mm) |
| Frets: | 22 Medium Jumbo Nickel Silver | 22 Medium Jumbo Nickel Silver |
| Fretboard Radius: | 10" | 10" |
| Nut: | PRS Propietary | PRS Propietary |
| Nut Width: | 42.9mm (1.688'') | 42.1mm (1.656'') |
| Electronics | ||
| Bridge Pickups: | Narrowfield DD "S" (Humbucker / Passive) | PRS DGT S (Humbucker / Passive) |
| Middle Pickup: | Narrowfield DD "S" (Humbucker / Passive) | |
| Neck Pickup: | Narrowfield DD "S" (Humbucker / Passive) | PRS DGT S (Humbucker / Passive) |
| Switch: | 5 Way | 3 Way |
| Knobs: | Speed | Speed |
| Pickup Mods: | None | Coil Split |
| Volume Controls: | 1 | 2 |
| Tone Controls: | 1 | 1 |
| Hardware | ||
| Strap Lock: | No | No |
| Hardware Color: | Nickel | Nickel |
Show Diagrams Comparison
Reasons to Get
PRS SE NF3 over SE DGT
Reasons to Get
PRS SE DGT over SE NF3
Other Key Differences
PRS SE NF3 vs SE DGT
Shared Features
PRS SE NF3 vs SE DGT
Common Strengths
- High-Quality Nut
- Top Pickup Brand
- Expensive Wood
Common Weaknesses
- Weight Relief
- Locking Tuners
- Stays in Tune (Evertune)
- High-Quality Frets
- Compound Radius Fretboard
- From a High-Quality-Standards Country
- Luminescent Sidedots
- Strap Lock
- 21:1 Tuner Ratio
- Active/Passive Preamp
Price History Comparison
These are affiliate links. We may earn a fee if you purchase after clicking. These prices are prone to error. Make sure you're buying the right product after clicking on a link from our site. We are not liable if you buy the wrong product after following these links. As an Amazon Associate site we earn from qualifying purchases.
Hand Size Comfortability
After taking into account the scale length, nut width, neck profile and fretboard radius, we can conclude that both favor small hands .
PRS SE NF3:
PRS SE DGT:
Beginner Friendliness
The PRS SE DGT meets 5 out of our 8 criteria items for beginner friendliness, while the PRS SE NF3 meets only 4. This takes into account the type of frets, scale length, nut width, bridge type, fretboard radius, and neck profile to determine the easiest combination for new players.
New Player Friendliness
PRS SE NF3- Comfortable shape
- Easy-to-use bridge
- Tall frets
- Comfortable neck
- Comfortable fretboard
- Narrow nut
- Short scale
- Locking tuners
New Player Friendliness
PRS SE DGT- Comfortable shape
- Easy-to-use bridge
- Tall frets
- Narrow nut
- Comfortable neck
- Comfortable fretboard
- Short scale
- Locking tuners
Sound Quality Comparison
The wood used in an electric guitar or bass is not as important to determine the final tone. However, some people prefer specific wood types, so we'll take a look at those first. Then, we'll take a look at the electronics to determine the versatility and sound quality of each instrument.
Woods Used in Both
Rosewood is an almost purple-looking wood that is used mainly for fretboards since it's heavy, rare, and expensive. It's sometimes used on acoustic guitar bodies to create stronger warm tones. Find out more about Rosewood.
Woods Used in the PRS SE NF3
Maple is one of the most popular necks for good reasons. It is a strong wood that is relatively cheap to make and looks beautiful. The highest quality maple is the hardest that comes from North America. Find out more about Maple.
Poplar is a cheaper and heavier alternative to Alder wood. It terms of tone, it emphasizes the low-end and has cutting mids. It's relatively soft compared to most body woods. Find out more about Poplar.
Woods Used in the PRS SE DGT
Mahogany is a fairly rare wood nowadays. It's used mostly for bodies due to its relatively lightweight. Gibson popularized it with their Les Paul guitars during their golden years, so this wood has a lot of good reputation behind it. The most expensive type comes from South America and it's still used by Gibson even today. Find out more about Mahogany.
Winner: PRS SE DGT.
Pickup Configuration
The PRS SE NF3 has an HHH configuration while the PRS SE DGT has HH pickups.
A triple Humbucker (HHH) can be intimidating at first, but it's one of the combinations that offer the most tone versatility. You'll be able to have from a lot of output for Hard Rock genres, to warm and clean sounds that are more common in Jazz.
On the other hand, Double Humbucker (HH) is the choice for people who want a fuller, more round sound with tons of mids and lows. Humbuckers also get rid of the hum noise that plague single-coil pickups. They can work out for almost any genre going from Djent to even Jazz.
Pickups Quality
Both come with very good pickups from at least one of the specialized brands in the market. With pickups like these, you probably won't need an upgrade anytime soon.
Both use Passive pickups. This is what's used for most music genres. They have a regular output and will serve you for both high-gain and clean tones. The alternative (Active pickups) offer a higher output that is mostly used for heavy music.
Winner: Tie.
Versatility Comparison
Some instruments offer you more ways to explore your creativity than others. Below you'll find how both compare when it comes to versatility.
Switch Options
The PRS SE NF3 gives you 5 switch options while the PRS SE DGT gives you 3. This means that the PRS SE NF3 gives you more options to find the right pickup combination for the type of sound you want to achieve
Only the PRS SE DGT comes with some kind of pickup modification: Coil Split.
Coil Split lets you disconnect one of the pickup coils. When used with humbuckers, it turns them into single-coil with lower output and cleaner tone.
When evaluating versatility, we also take into consideration bridge and neck joint type, number of frets, switch options, amount of pickups and more.
Winner: PRS SE DGT.
Final Sound Quality Scores
Build Quality Comparison
When it comes to build quality, we like to take into account everything used to build the instrument. This includes materials, hardware and the quality control expected depending on the country where it was built. Let's see how the PRS SE NF3 compares to the PRS SE DGT.
Country of Origin
The manufacturing country can tell a lot about the build quality of an instrument. Both in this comparison where made in Indonesia.
Indonesia is becoming the most popular country for guitar building because they can make good instruments for a low price. Some people think that they're 'the new China' when it comes to build quality. But the truth is that Indonesian guitars are more consistent, although Chinese quality has improved a lot in the last few years.
Winner: Tie
Nut Material
If you want your guitar to stay in tune and sound good, you need a well cut nut. Nut quality can be inconsistent even when comparing two copies of the same model. The best way to make sure you're nut will be well done is by getting a nut made by an expert company like TUSQ or Micarta.
In this case, both have PRS Propietary nuts. It's similar to TUSQ nuts, but they're not as hard, and the tone is not as bright. However, the material is self-lubricating, and it's usually well cut, so they have good tuning stability.
Fret Material
Most fret wire is made of nickel silver. This material eventually wears down after a lot of use and most instruments end up needing a complete fret replacement. However, some expensive models come with stainless steel frets. This is what you should aim for if you can afford it.
Unfortunately, none of them come with stainless steel frets.
Winner: Tie.
Bridge
The perfect bridge for you will depend on your playstyle because they all have advantages and disadvantages. However, some bridges are more expensive—like Floyd Roses and Evertunes—and thus add more value to a guitar.
Both come with a similar bridge: Tremolo. Tremolo bridges give you more versatility than fixed bridges. They let you perform the intense vibrato effects that would be impossible with a fixed bridge. However, since the bridge floats and there's less contact with the body, the strings lose sustain slightly faster. They can also be a bit harder to restring and set up correctly than fixed bridges.
Since we need to be objective, the most expensive type of bridge will be the winner of this section. In the end, this doesn't matter if you're not going to use the bridge for its original purpose, so choose the bridge that fits your playing style better.
Winner: Tie.
Tuners
Both come with regular tuners. The PRS SE NF3's are PRS Designed while the PRS SE DGT's are PRS Designed Tuners
Winner: Tie.
Neck Joint
Contrary to popular belief, the difference in sustain and tone that some neck joints give to a guitar is simply unperceivable—if they're all well built. However, some of them do have advantages over the others.
The PRS SE NF3 has a Bolt-On neck joint. This neck is joined to the body by 4 bolts that you can simply unscrew. This allows you to replace the neck or take it off for travel. It's the most common and cheapest way to build a guitar.
On the other hand, the PRS SE DGT comes with Set neck joint. This neck is tightly glued to the body. They give you the least versatility because you can't swap them for a neck that fits your hand better if you want to, unlike bolt-on necks. Some people think this gives more resonance and sustain, but there's no real difference if the bolt-on joint is well built.
Winner: PRS SE NF3.
Here is the list of features that were considered when choosing the winner in the Features subcategory:
PRS SE NF3
- Expensive Wood
- PRS Propietary Nut
- Top Brand Pickups
- Tremolo
- Cheap Fret Wire (NS)
- No Locking Tuners
- Made in Indonesia
- No Neck-Through Build
- No Push Knob or Extra Switch Option
- No Weight Relief
- No Luminescent Inlay
- No Compound Radius Fretboard
- No 21:1 Tuner Ratio
- No Strap Lock
PRS SE DGT
- Expensive Wood
- PRS Propietary Nut
- Top Brand Pickups
- Coil Split Pickups
- Tremolo
- Cheap Fret Wire (NS)
- No Locking Tuners
- Made in Indonesia
- No Neck-Through Build
- No Weight Relief
- No Luminescent Inlay
- No Compound Radius Fretboard
- No 21:1 Tuner Ratio
- No Strap Lock
Final Build Quality Scores
Playability Comparison
Let's now compare their playability. Bear in mind that the instrument will feel different depending on your hand size and play style. That's why you should always test before buying. But if you can't or want a second opinion on it, we can still take a look at each of the important measurements of the instrument for you. This way, we can predict how easy a guitar might be to play, or how different it will feel compared to the other.
Remember that, even though the difference might seem small, every inch counts when it comes to feeling of the instrument in your hands. Any variation can completely change how comfortable a guitar feels in your hands.
Nut Width
The nut width will affect the separation between strings at the nut. In this comparison, the PRS SE NF3 has the wider nut with 42.9mm (1.688'') vs 42.1mm (1.656''). This is a 0.8mm (0.032'') difference
This means that it will be more difficult to do bar chords on the PRS SE NF3, especially closer to the nut. However, it's also easier to play without muting strings accidently. This favors people with big hands.
Scale Length
The scale length is one of the things that influences playability the most. This is the distance between the nut and the bridge and will affect everything from low action allowance, difficulty to perform bends, fret separation, and even tone.
In this case, both have a scale length of 25".
This scale is close to a Les Paul (24.75''), but it's slightly longer for those who want more tension of the strings and a slightly brighter sound (but not as much as with a 25.5'' Stratocaster scale).
This longer scale will also mean the frets are slightly more separated, which can affect your speed when playing. However, since this increases the tension of the strings, it will also allow you to lower the action even further without getting fret buzz. It comes at the cost of making the strings feel stiffer, which makes bending more difficult, though.
However, remember that you can also change the tension of the strings by using different string gauges.
Lastly, remember that you can also affect the tension of the strings by changing your string gauge. You can use a thicker gauge for more tension and a lighter one for less tension.
Neck Profile
No single neck shape is better than others. However, most people tend to prefer a thinner necks because it doesn't get in their way when playing fast and most hand sizes can adapt to it pretty well. However, some people still prefer thicker necks for a better grip, especially if they have big hands.
Both the PRS SE NF3 and the PRS SE DGT have a C-shaped neck. This is what you'll find in most modern guitars. Most people feel like the thickness of a C neck is simply the less intrusive one for playing fast, while at the same time allowing you to grab the neck easily for resting if you want to.
Fretboard Radius
Most guitar fretboards are not flat; they usually have a curve or arc across their width. A curved fretboard will make it easier to perform chords without muting strings, while a flatter one will make it easier to play single notes, which is good for bending and soloing in general. The best fretboards have a compound radius that varies across the fingerboard, but they're not common since they take a lot more work to build.
Both the PRS SE NF3 and the PRS SE DGT have the same fretboard radius of 10". This is slightly flatter than the typical modern Stratocaster, but not by a lot. This radius will make it comfortable to play chords without muting strings accidentally. However, when compared to Strats, the extra .5 inches radius will make it slightly more comfortable to play solos without sacrificing too much chord playability.
Fret Size
Both have a Medium Jumbo fret size. These are slightly shorter than full Jumbo frets, so you'll still feel the fretboard when pressing down the strings. However, they interfere less with your fretting hand than medium-size frets. This is a good size if you like easy-to-press frets, but would still like to feel a bit of the fretboard when playing.
