Show Full Spec Comparison
| Fender Player II Stratocaster HSS | Sterling Albert Lee | |
|---|---|---|
| General | ||
| Brand: | Fender | Sterling |
| Year: | 2024 | 2020 |
| Configuration: | HSS | HH |
| Strings: | 6 | 6 |
| Made in: | Mexico | Indonesia |
| Series: | Player II | Artist |
| Colors: | White, Sunburst, Blue, Green, Red, Yellow | Blue |
| Left-Handed Version: | No | No |
| Body | ||
| Type: | Solid Body | Solid Body |
| Body Material: | Alder | Mahogany |
| Bridge: | 2-Point Synchronized Tremolo with Bent Steel Saddles | Fulcrum Tremolo |
| Neck | ||
| Neck Joint: | Bolt-On | Bolt-On |
| Tuners: | Fender ClassicGear | Diecast |
| Fretboard: | Slab Rosewood | Jatoba |
| Neck Material: | Maple | Hard Maple |
| Decoration: | White Dot | Black/White Dot Markers |
| Scale Size: | 25.5" | 25.5" |
| Shape: | Modern "C" | Albert Lee |
| Frets: | 22 Medium Jumbo Nickel Silver | 22 Narrow Tall Nickel Silver |
| Fretboard Radius: | 9.5" | 9.5" |
| Nut: | Synthetic Bone | Compensated |
| Nut Width: | 41.9mm (1.65'') | 41.9mm (1.65'') |
| Electronics | ||
| Bridge Pickups: | Player Series Alnico 2 Humbucker (Humbucker / Passive) | Sterling Humbucker (Humbucker / Passive) |
| Middle Pickup: | Player Series Alnico 5 Strat Single-Coil (Single Coil / Passive) | |
| Neck Pickup: | Player Series Alnico 5 Strat Single-Coil (Single Coil / Passive) | Sterling Humbucker (Humbucker / Passive) |
| Switch: | 5 Way | 5 Way |
| Knobs: | Bell | Dome |
| Pickup Mods: | None | None |
| Volume Controls: | 1 | 1 |
| Tone Controls: | 2 | 1 |
| Hardware | ||
| Strap Lock: | No | No |
| Hardware Color: | Nickel | Chrome |
Show Diagrams Comparison
Reasons to Get
Fender Player II Stratocaster HSS over Sterling Albert Lee
Reasons to Get
Sterling Albert Lee over Fender Player II Stratocaster HSS
Other Key Differences
Fender Player II Stratocaster HSS vs Sterling Albert Lee
Shared Features
Fender Player II Stratocaster HSS vs Sterling Albert Lee
Common Strengths
- High-Quality Nut
- Expensive Wood
Common Weaknesses
- Neck-Through Build
- Pickup Alter Switch/Knob
- Locking Tuners
- Stays in Tune (Evertune)
- High-Quality Frets
- Compound Radius Fretboard
- From a High-Quality-Standards Country
- Luminescent Sidedots
- Strap Lock
- 21:1 Tuner Ratio
- Active/Passive Preamp
Price History Comparison
These are affiliate links. We may earn a fee if you purchase after clicking. These prices are prone to error. Make sure you're buying the right product after clicking on a link from our site. We are not liable if you buy the wrong product after following these links. As an Amazon Associate site we earn from qualifying purchases.
Hand Size Comfortability
After taking into account the scale length, nut width, neck profile and fretboard radius, we can conclude that both favor small hands .
Fender Player II Stratocaster HSS:
Sterling Albert Lee:
Beginner Friendliness
Both meet 6 out of our 8 criteria items for beginner friendliness. This takes into account the type of frets, scale length, nut width, bridge type, fretboard radius, and neck profile to determine the easiest combination for new players. If you're looking for your first guitar to learn how to play, you can't go wrong with either of them.
New Player Friendliness
Fender Player II Stratocaster HSS- Comfortable shape
- Easy-to-use bridge
- Comfortable fretboard
- Tall frets
- Narrow nut
- Comfortable neck
- Short scale
- Locking tuners
New Player Friendliness
Sterling Albert Lee- Comfortable shape
- Easy-to-use bridge
- Comfortable fretboard
- Tall frets
- Narrow nut
- Comfortable neck
- Short scale
- Locking tuners
Sound Quality Comparison
The wood used in an electric guitar or bass is not as important to determine the final tone. However, some people prefer specific wood types, so we'll take a look at those first. Then, we'll take a look at the electronics to determine the versatility and sound quality of each instrument.
Woods Used in Both
Maple is one of the most popular necks for good reasons. It is a strong wood that is relatively cheap to make and looks beautiful. The highest quality maple is the hardest that comes from North America. Find out more about Maple.
Woods Used in the Fender Player II Stratocaster HSS
Rosewood is an almost purple-looking wood that is used mainly for fretboards since it's heavy, rare, and expensive. It's sometimes used on acoustic guitar bodies to create stronger warm tones. Find out more about Rosewood.
Alder is the most popular wood that Fender uses in most of their guitars nowadays. Even though they say it's because of its balanced tone with an emphasis in the upper midrange, it probably is because it isn't too expensive, and it's also pretty lightweight—more than Mahogany. Find out more about Alder.
Woods Used in the Sterling Albert Lee
Jatoba is a hard and dense wood that emphasizes the mid-lows, giving a fuller, more round sound than, for example, Mahogany. However, it also has a lot of clarity in the top end. Find out more about Jatoba.
Mahogany is a fairly rare wood nowadays. It's used mostly for bodies due to its relatively lightweight. Gibson popularized it with their Les Paul guitars during their golden years, so this wood has a lot of good reputation behind it. The most expensive type comes from South America and it's still used by Gibson even today. Find out more about Mahogany.
Winner: Tie.
Pickup Configuration
The Fender Player II Stratocaster HSS has an HSS configuration while the Sterling Albert Lee has HH pickups.
HSS provides a great balance if you like to play with a lot of distortion, but also love to use clean tones. You'll get a lot of output at the bridge position, but you'll be able to play bright clean tones at the other positions.
On the other hand, Double Humbucker (HH) is the choice for people who want a fuller, more round sound with tons of mids and lows. Humbuckers also get rid of the hum noise that plague single-coil pickups. They can work out for almost any genre going from Djent to even Jazz.
Pickups Quality
The Fender Player II Stratocaster HSS has pickups from a more specialized brand than the Sterling Albert Lee. Its pickups should simply give you a better, fuller sound, although it all depends on what type of music you're going to play. We recommend these pickups for Hard Rock and similar genres.
Both use Passive pickups. This is what's used for most music genres. They have a regular output and will serve you for both high-gain and clean tones. The alternative (Active pickups) offer a higher output that is mostly used for heavy music.
Winner: Fender Player II Stratocaster HSS.
Versatility Comparison
Some instruments offer you more ways to explore your creativity than others. Below you'll find how both compare when it comes to versatility.
Switch Options
Both are equal when it comes to the pickup switching option.
Neither of them come with some kind of coil split or pickup mod option. This makes both lacking in terms of versatility.
When evaluating versatility, we also take into consideration bridge and neck joint type, number of frets, switch options, amount of pickups and more.
Winner: Fender Player II Stratocaster HSS.
Final Sound Quality Scores
Build Quality Comparison
When it comes to build quality, we like to take into account everything used to build the instrument. This includes materials, hardware and the quality control expected depending on the country where it was built. Let's see how the Fender Player II Stratocaster HSS compares to the Sterling Albert Lee.
Country of Origin
The manufacturing country can tell a lot about the build quality of an instrument. The Fender Player II Stratocaster HSS is built in Mexico while the Sterling Albert Lee is made in Indonesia.
Mexico has been for a long time where Fender has built their semi-premium series. If you don't want to overpay for a wellp-built instrument, a guitar built in this country by a good brand always offers good value for the money.
Indonesia is becoming the most popular country for guitar building because they can make good instruments for a low price. Some people think that they're 'the new China' when it comes to build quality. But the truth is that Indonesian guitars are more consistent, although Chinese quality has improved a lot in the last few years.
Winner: Tie
Nut Material
If you want your guitar to stay in tune and sound good, you need a well cut nut. Nut quality can be inconsistent even when comparing two copies of the same model. The best way to make sure you're nut will be well done is by getting a nut made by an expert company like TUSQ or Micarta.
The Fender Player II Stratocaster HSS has a Synthetic Bone nut. Bone is the best natural material for guitar nuts. However, its tonal properties can be inconsistent. That's the problem that synthetic bone fixes. This is much better than using a plastic nut because the nut is more slippery—which helps with tuning stability—, and it gives your open strings rich harmonics.
On the other hand, the Sterling Albert Lee comes with a Compensated nut. Each hole where the string sits at the nut is cut at a different distance from the bridge, which compensates for the different amount of tension that each string is subject to. This fixes most intonation issues across the fretboard, so it gives great tuning stability.
Winner: Tie.
Fret Material
Most fret wire is made of nickel silver. This material eventually wears down after a lot of use and most instruments end up needing a complete fret replacement. However, some expensive models come with stainless steel frets. This is what you should aim for if you can afford it.
Unfortunately, none of them come with stainless steel frets.
Winner: Tie.
Bridge
The perfect bridge for you will depend on your playstyle because they all have advantages and disadvantages. However, some bridges are more expensive—like Floyd Roses and Evertunes—and thus add more value to a guitar.
Both come with a similar bridge: Tremolo. Tremolo bridges give you more versatility than fixed bridges. They let you perform the intense vibrato effects that would be impossible with a fixed bridge. However, since the bridge floats and there's less contact with the body, the strings lose sustain slightly faster. They can also be a bit harder to restring and set up correctly than fixed bridges.
Since we need to be objective, the most expensive type of bridge will be the winner of this section. In the end, this doesn't matter if you're not going to use the bridge for its original purpose, so choose the bridge that fits your playing style better.
Winner: Tie.
Tuners
Both come with regular tuners. The Fender Player II Stratocaster HSS's are Fender ClassicGear while the Sterling Albert Lee's are Diecast
Winner: Tie.
Neck Joint
Contrary to popular belief, the difference in sustain and tone that some neck joints give to a guitar is simply unperceivable—if they're all well built. However, some of them do have advantages over the others.
Both have a Bolt-On neck joint. This neck is joined to the body by 4 bolts that you can simply unscrew. This allows you to replace the neck or take it off for travel. It's the most common and cheapest way to build a guitar.
Winner: Tie.
Here is the list of features that were considered when choosing the winner in the Features subcategory:
Fender Player II Stratocaster HSS
- Expensive Wood
- Synthetic Bone Nut
- Top Brand Pickups
- Weight Relief
- Tremolo
- Cheap Fret Wire (NS)
- No Locking Tuners
- Made in Mexico
- No Neck-Through Build
- No Push Knob or Extra Switch Option
- No Luminescent Inlay
- No Compound Radius Fretboard
- No 21:1 Tuner Ratio
- No Strap Lock
Sterling Albert Lee
- Expensive Wood
- Compensated Nut
- Tremolo
- Cheap Fret Wire (NS)
- No Locking Tuners
- Made in Indonesia
- No Top Brand Pickups
- No Neck-Through Build
- No Push Knob or Extra Switch Option
- No Weight Relief
- No Luminescent Inlay
- No Compound Radius Fretboard
- No 21:1 Tuner Ratio
- No Strap Lock
Final Build Quality Scores
Playability Comparison
Let's now compare their playability. Bear in mind that the instrument will feel different depending on your hand size and play style. That's why you should always test before buying. But if you can't or want a second opinion on it, we can still take a look at each of the important measurements of the instrument for you. This way, we can predict how easy a guitar might be to play, or how different it will feel compared to the other.
Remember that, even though the difference might seem small, every inch counts when it comes to feeling of the instrument in your hands. Any variation can completely change how comfortable a guitar feels in your hands.
Nut Width
The nut width will affect the separation between strings at the nut. In this comparison, both have a nut width of 41.9mm (1.65'').
This is considered a narrow width for a 6-string guitar. This means that this guitar will have a narrower string separation at the nut, which will affect your fretting hand.
If you are a player with big hands, you might find it difficult to play chords without muting strings. However, this is good for players who have smaller hands, as it will allow them to reach each string more easily at the nut.
Scale Length
The scale length is one of the things that influences playability the most. This is the distance between the nut and the bridge and will affect everything from low action allowance, difficulty to perform bends, fret separation, and even tone.
In this case, both have a scale length of 25.5".
This is the scale used in most Stratocasters. It's slightly longer than the typical 24.75'' size found in Les Pauls, and it's one of the main reasons why Stratocasters have such a bright sound in general. A longer scale also means that the strings will have higher tension. This will help you get lower action without suffering fret buzz, which will also be helpful when playing in lower tunings without having to increase your string gauge.
However, this also means that there will be more separation between frets, which can make it more difficult to play. Also, bending the strings will require more strengths due to the increased tension, but remember that a tremolo guitar will offset this difficulty.
Lastly, remember that you can also affect the tension of the strings by changing your string gauge. You can use a thicker gauge for more tension and a lighter one for less tension.
Neck Profile
No single neck shape is better than others. However, most people tend to prefer a thinner necks because it doesn't get in their way when playing fast and most hand sizes can adapt to it pretty well. However, some people still prefer thicker necks for a better grip, especially if they have big hands.
Both the Fender Player II Stratocaster HSS and the Sterling Albert Lee have a C-shaped neck. This is what you'll find in most modern guitars. Most people feel like the thickness of a C neck is simply the less intrusive one for playing fast, while at the same time allowing you to grab the neck easily for resting if you want to.
Fretboard Radius
Most guitar fretboards are not flat; they usually have a curve or arc across their width. A curved fretboard will make it easier to perform chords without muting strings, while a flatter one will make it easier to play single notes, which is good for bending and soloing in general. The best fretboards have a compound radius that varies across the fingerboard, but they're not common since they take a lot more work to build.
Both the Fender Player II Stratocaster HSS and the Sterling Albert Lee have the same fretboard radius of 9.5". This is the most common radius for Stratocaster guitars. It's considered curved when compared to most other models. This allows you to play chords very easily without muting strings accidentally and gives you more space between strings for fingerpicking. However, this curve also gives the guitar less allowance for lower action. If you bend too hard at the high frets, some of your notes might get muted because the curve will make the string fret out.
Fret Size
The Sterling Albert Lee has Narrow Tall frets, which should be taller than the Fender Player II Stratocaster HSS's Medium Jumbo frets.
Some people prefer taller frets because they result in more sustain since the strings get pressed cleanly without interference from the fretboard. However, if they're too tall—like Jumbo frets—, you might change the pitch of the strings accidentally if you press too hard because you won't be touching the fretboard with your fingers. This is also why some guitarists with a heavy grip prefer smaller frets. They like to feel the fingerboard to avoid pressing down too hard and getting out of pitch.
