Show Full Spec Comparison
| Fender Made in Japan Limited International Color Telecaster | PRS McCarty Singlecut 594 | |
|---|---|---|
| General | ||
| Brand: | Fender | PRS |
| Year: | 2023 | 2016 |
| Configuration: | SS | HH |
| Strings: | 6 | 6 |
| Made in: | Japan | United States |
| Series: | Made in Japan Limited International | Core |
| Colors: | Gold, White, Black, Blue, Green, Black Burst, Orange, Purple, Yellow, Red Burst, Gold Burst, Dark Cherry Sunburst, McCarty Sunburst, McCarty Tobacco Sunburst | |
| Left-Handed Version: | No | No |
| Body | ||
| Type: | Solid Body | Solid Body |
| Body Material: | Basswood | Mahogany |
| Bridge: | 3-Saddle Vintage-Style Strings-Through-Body Tele with Chrome Barrel Saddles | PRS Two-Piece, Cast Zinc |
| Neck | ||
| Neck Joint: | Bolt-On | Set |
| Tuners: | Fender Vintage F Stamped | Vintage-Style |
| Fretboard: | Maple | Rosewood w/ Faux Bone Binding |
| Neck Material: | Maple | Mahogany |
| Decoration: | Black Dot | Old School Birds |
| Scale Size: | 25.5" | 24.6" |
| Shape: | U Shape | Pattern Vintage |
| Frets: | 21 Medium Jumbo Nickel Silver | 22 Medium Jumbo Nickel Silver |
| Fretboard Radius: | 9.5" | 10" |
| Nut: | Bone | Bone |
| Nut Width: | 41mm (1.615'') | 42.9mm (1.688'') |
| Electronics | ||
| Bridge Pickups: | Fender Vintage-Style Single-Coil Tele (Single Coil / Passive) | PRS 58/15 LT + (Humbucker / Passive) |
| Middle Pickup: | ||
| Neck Pickup: | Fender Vintage-Style Single-Coil Tele (Single Coil / Passive) | PRS 58/15 LT + (Humbucker / Passive) |
| Switch: | 3 Way | 3 Way |
| Knobs: | Dome | Speed |
| Pickup Mods: | None | Coil Split |
| Volume Controls: | 1 | 2 |
| Tone Controls: | 1 | 2 |
| Hardware | ||
| Strap Lock: | No | No |
| Hardware Color: | Chrome | Nickel |
Show Diagrams Comparison
Reasons to Get
Fender Made in Japan Limited International Color Telecaster over PRS McCarty Singlecut 594
Reasons to Get
PRS McCarty Singlecut 594 over Fender Made in Japan Limited International Color Telecaster
Other Key Differences
Fender Made in Japan Limited International Color Telecaster vs PRS McCarty Singlecut 594
Shared Features
Fender Made in Japan Limited International Color Telecaster vs PRS McCarty Singlecut 594
Common Strengths
- High-Quality Nut
- From a High-Quality-Standards Country
- Top Pickup Brand
Common Weaknesses
- Weight Relief
- Locking Tuners
- Stays in Tune (Evertune)
- High-Quality Frets
- Compound Radius Fretboard
- Luminescent Sidedots
- Strap Lock
- 21:1 Tuner Ratio
- Active/Passive Preamp
Price History Comparison
These are affiliate links. We may earn a fee if you purchase after clicking. These prices are prone to error. Make sure you're buying the right product after clicking on a link from our site. We are not liable if you buy the wrong product after following these links. As an Amazon Associate site we earn from qualifying purchases.
Hand Size Comfortability
After taking into account the scale length, nut width, neck profile and fretboard radius, we can conclude that both are balanced for most hand sizes.
Fender Made in Japan Limited International Color Telecaster:
PRS McCarty Singlecut 594:
Beginner Friendliness
The Fender Made in Japan Limited International Color Telecaster meets 6 out of our 8 criteria items for beginner friendliness, while the PRS McCarty Singlecut 594 meets only 4. This takes into account the type of frets, scale length, nut width, bridge type, fretboard radius, and neck profile to determine the easiest combination for new players.
New Player Friendliness
Fender Made in Japan Limited International Color Telecaster- Comfortable shape
- Easy-to-use bridge
- Comfortable fretboard
- Tall frets
- Narrow nut
- Comfortable neck
- Short scale
- Locking tuners
New Player Friendliness
PRS McCarty Singlecut 594- Comfortable shape
- Easy-to-use bridge
- Tall frets
- Short scale
- Comfortable fretboard
- Narrow nut
- Comfortable neck
- Locking tuners
Sound Quality Comparison
The wood used in an electric guitar or bass is not as important to determine the final tone. However, some people prefer specific wood types, so we'll take a look at those first. Then, we'll take a look at the electronics to determine the versatility and sound quality of each instrument.
Woods Used in the Fender Made in Japan Limited International Color Telecaster
Maple is one of the most popular necks for good reasons. It is a strong wood that is relatively cheap to make and looks beautiful. The highest quality maple is the hardest that comes from North America. Find out more about Maple.
Basswood is a lightweight type of wood that isn't as expensive as other popular choices for guitar building. It gives more power to the mid-range frequencies. Its color can vary from pale white to light brown. Find out more about Basswood.
Woods Used in the PRS McCarty Singlecut 594
Mahogany is a fairly rare wood nowadays. It's used mostly for bodies due to its relatively lightweight. Gibson popularized it with their Les Paul guitars during their golden years, so this wood has a lot of good reputation behind it. The most expensive type comes from South America and it's still used by Gibson even today. Find out more about Mahogany.
Rosewood is an almost purple-looking wood that is used mainly for fretboards since it's heavy, rare, and expensive. It's sometimes used on acoustic guitar bodies to create stronger warm tones. Find out more about Rosewood.
Winner: PRS McCarty Singlecut 594.
Pickup Configuration
The Fender Made in Japan Limited International Color Telecaster has an SS configuration while the PRS McCarty Singlecut 594 has HH pickups.
SS is the classic Telecaster configuration. It's used mainly for playing clean or with low-gain distortion, and it's very popular for the country genre because of their brightness. It doesn't give you as much versatility as a Strat SSS configuration, but you might like the cleaner look of a guitar body with fewer pickups.
On the other hand, Double Humbucker (HH) is the choice for people who want a fuller, more round sound with tons of mids and lows. Humbuckers also get rid of the hum noise that plague single-coil pickups. They can work out for almost any genre going from Djent to even Jazz.
Pickups Quality
Both come with very good pickups from at least one of the specialized brands in the market. With pickups like these, you probably won't need an upgrade anytime soon.
However, the Fender Made in Japan Limited International Color Telecaster has a slight sound quality advantage when taking into account other factors like the type of pickups, magnet, position, etc.
You can purchase similar pickups to the Fender Made in Japan Limited International Color Telecaster's and use them on any guitar:
Both use Passive pickups. This is what's used for most music genres. They have a regular output and will serve you for both high-gain and clean tones. The alternative (Active pickups) offer a higher output that is mostly used for heavy music.
Winner: Fender Made in Japan Limited International Color Telecaster.
Versatility Comparison
Some instruments offer you more ways to explore your creativity than others. Below you'll find how both compare when it comes to versatility.
Switch Options
Both are equal when it comes to the pickup switching option.
Only the PRS McCarty Singlecut 594 comes with some kind of pickup modification: Coil Split.
Coil Split lets you disconnect one of the pickup coils. When used with humbuckers, it turns them into single-coil with lower output and cleaner tone.
When evaluating versatility, we also take into consideration bridge and neck joint type, number of frets, switch options, amount of pickups and more.
Winner: PRS McCarty Singlecut 594.
Final Sound Quality Scores
Build Quality Comparison
When it comes to build quality, we like to take into account everything used to build the instrument. This includes materials, hardware and the quality control expected depending on the country where it was built. Let's see how the Fender Made in Japan Limited International Color Telecaster compares to the PRS McCarty Singlecut 594.
Country of Origin
The manufacturing country can tell a lot about the build quality of an instrument. The Fender Made in Japan Limited International Color Telecaster is built in Japan while the PRS McCarty Singlecut 594 is made in United States.
Japan has a long history of high-quality guitar building. Little has changed in terms of their manufacturing and quality control over the years. Many guitars made in this country can be compared—and even beat—others made in the US.
The United States is considered one of the best electric guitar manufacturers in the world. A guitar made in this country is supposed to have world-class quality control. Nowadays, guitars made in other countries can beat some of the ones made in the US, but most of the time, this country offers the best you can get. Of course, that comes at a price.
Winner: Tie
Nut Material
If you want your guitar to stay in tune and sound good, you need a well cut nut. Nut quality can be inconsistent even when comparing two copies of the same model. The best way to make sure you're nut will be well done is by getting a nut made by an expert company like TUSQ or Micarta.
In this case, both have Bone nuts. It's a type of nut found in high-quality instruments. They sound similar to Ivory since they give a lot of sustain and a bright sound (at least when striking open strings). The only problem they can run into is that you may get a bone piece that simply doesn't sound as well as others because that's just how natural materials are.
Fret Material
Most fret wire is made of nickel silver. This material eventually wears down after a lot of use and most instruments end up needing a complete fret replacement. However, some expensive models come with stainless steel frets. This is what you should aim for if you can afford it.
Unfortunately, none of them come with stainless steel frets.
Winner: Tie.
Bridge
The perfect bridge for you will depend on your playstyle because they all have advantages and disadvantages. However, some bridges are more expensive—like Floyd Roses and Evertunes—and thus add more value to a guitar.
Both come with a similar bridge: Fixed. It's a simple bridge that is very beginner-friendly since it doesn't require any set-up. You can swap strings easily. It might also give more sustain since it doesn't have complex moving parts that make the strings lose vibration. However, it doesn't have the same versatility as a tremolo bridge.
Since we need to be objective, the most expensive type of bridge will be the winner of this section. In the end, this doesn't matter if you're not going to use the bridge for its original purpose, so choose the bridge that fits your playing style better.
Winner: Tie.
Tuners
Both come with regular tuners. The Fender Made in Japan Limited International Color Telecaster's are Fender Vintage F Stamped while the PRS McCarty Singlecut 594's are Vintage-Style
Winner: Tie.
Neck Joint
Contrary to popular belief, the difference in sustain and tone that some neck joints give to a guitar is simply unperceivable—if they're all well built. However, some of them do have advantages over the others.
The Fender Made in Japan Limited International Color Telecaster has a Bolt-On neck joint. This neck is joined to the body by 4 bolts that you can simply unscrew. This allows you to replace the neck or take it off for travel. It's the most common and cheapest way to build a guitar.
On the other hand, the PRS McCarty Singlecut 594 comes with Set neck joint. This neck is tightly glued to the body. They give you the least versatility because you can't swap them for a neck that fits your hand better if you want to, unlike bolt-on necks. Some people think this gives more resonance and sustain, but there's no real difference if the bolt-on joint is well built.
Winner: Fender Made in Japan Limited International Color Telecaster.
Here is the list of features that were considered when choosing the winner in the Features subcategory:
Fender Made in Japan Limited International Color Telecaster
- Made in Japan
- Bone Nut
- Top Brand Pickups
- Cheap Fret Wire (NS)
- No Locking Tuners
- No Expensive Woods
- No Neck-Through Build
- No Push Knob or Extra Switch Option
- No Weight Relief
- No Luminescent Inlay
- No Tremolo
- No Compound Radius Fretboard
- No 21:1 Tuner Ratio
- No Strap Lock
PRS McCarty Singlecut 594
- Made in United States
- Expensive Wood
- Bone Nut
- Top Brand Pickups
- Coil Split Pickups
- Cheap Fret Wire (NS)
- No Locking Tuners
- No Neck-Through Build
- No Weight Relief
- No Luminescent Inlay
- No Tremolo
- No Compound Radius Fretboard
- No 21:1 Tuner Ratio
- No Strap Lock
Final Build Quality Scores
Playability Comparison
Let's now compare their playability. Bear in mind that the instrument will feel different depending on your hand size and play style. That's why you should always test before buying. But if you can't or want a second opinion on it, we can still take a look at each of the important measurements of the instrument for you. This way, we can predict how easy a guitar might be to play, or how different it will feel compared to the other.
Remember that, even though the difference might seem small, every inch counts when it comes to feeling of the instrument in your hands. Any variation can completely change how comfortable a guitar feels in your hands.
Nut Width
The nut width will affect the separation between strings at the nut. In this comparison, the PRS McCarty Singlecut 594 has the wider nut with 42.9mm (1.688'') vs 41mm (1.615''). This is a 1.9mm (0.073'') difference
This means that it will be more difficult to do bar chords on the PRS McCarty Singlecut 594, especially closer to the nut. However, it's also easier to play without muting strings accidently. This favors people with big hands.
Scale Length
The scale length is one of the things that influences playability the most. This is the distance between the nut and the bridge and will affect everything from low action allowance, difficulty to perform bends, fret separation, and even tone.
The Fender Made in Japan Limited International Color Telecaster has the longest scale: 25.5". The PRS McCarty Singlecut 594 is only 24.6" long. This is a 0.9'' (22.9mm) scale length difference.
This longer scale means that the strings need more tension to get in tune. This is good if you want to avoid fret buzz, which can happen when the strings are too loose and touch the frets while vibrating. This is especially important when playing in lower tunings. This will also let you reduce the gap between fretboard and strings (low action) to make them easier to press down. However, this higher tension will also make it harder to perform bends and vibratos as the strings will feel stiffer.
This also means that the frets have a longer separation between each other, so this will make it harder for people with smaller hands when playing some chord positions.
Another characteristic of a longer scale is that it makes the guitar sound 'snappier' or brighter. This is due to the extra separation between harmonics and overtones produced by the tension. This influences tone more than any other factor (except the pickups).
Lastly, remember that you can also affect the tension of the strings by changing your string gauge. You can use a thicker gauge for more tension and a lighter one for less tension.
Neck Profile
No single neck shape is better than others. However, most people tend to prefer a thinner necks because it doesn't get in their way when playing fast and most hand sizes can adapt to it pretty well. However, some people still prefer thicker necks for a better grip, especially if they have big hands.
In this case, both have different neck shapes:
The Fender Made in Japan Limited International Color Telecaster has a U type of neck. This is also referred to as ''baseball neck'' because of its shape. It's usually thick, which is why some people with big hands like it. However, they can also be thin, similar to a C shape, but with more shoulders for a better grip.
The PRS McCarty Singlecut 594, on the other hand, has a Asymmetrical neck. Even though this neck shape looks like a poorly-made job, it's, in fact, the neck that most naturally adapts to the arc of your hand when grabbing a guitar neck. You'll notice that the lower part of your palm makes a more pronounced, deeper curve while the upper part makes a more subtle arch. This is the shape that adapts the best to that natural arch your hand makes while playing.
Fretboard Radius
Most guitar fretboards are not flat; they usually have a curve or arc across their width. A curved fretboard will make it easier to perform chords without muting strings, while a flatter one will make it easier to play single notes, which is good for bending and soloing in general. The best fretboards have a compound radius that varies across the fingerboard, but they're not common since they take a lot more work to build.
In this case, the Fender Made in Japan Limited International Color Telecaster's fingerboard radius is smaller, which means it's more curved than the PRS McCarty Singlecut 594's. This extra arc will make playing chords easier in this model. You won't be as likely to mute the strings, especially if you have big hands. However, playing single notes and bending will be easier on the PRS McCarty Singlecut 594.
Still, both are closer to a Stratocaster radius than a Les Paul, so both of them will favor chord playing rather than soloing.
Fret Size
Both have a Medium Jumbo fret size. These are slightly shorter than full Jumbo frets, so you'll still feel the fretboard when pressing down the strings. However, they interfere less with your fretting hand than medium-size frets. This is a good size if you like easy-to-press frets, but would still like to feel a bit of the fretboard when playing.
